HOME / How to tighten the generator belt of Fengjun 5

How to tighten the generator belt of Fengjun 5

Belt tension question

A new belt will stretch a little as it ''breaks in''. Really wrenching down the belt overly hard isn''t good for the bearings in the alt and p/s pump. Generally I set them about how the diagram shows, then sometimes after a

1958-1967

If you have to really push hard with your thumb on the middle of the fan belt to get it to deflect the factory spec of 0.6" then it''s too tight. Firm pressure at most is all that''s needed when checking the belt deflection. The

Tighten the belts (239)

Generator is mounted to the bracket with the "strap". The bolt for the generator bracket (7/8 head) and the 2 for the fan hub (5/8 head) are all loose. Here comes finally the question! I was reading somewhere you could

How to Adjust Genset Fan Belt And Clearance of

5. Do not let the belt rub any close parts. 6. Adjust the belt to the appropriate tension. All new belts will become loose after running for an hour or an hour, so they must be readjusted to the requirement of "belt tensioning

Changing generator, 4-cyl. LHD 9-5 (9600) 2003 | SAAB Workshop

Face the generator and belt pulley downwards between the steering gear and the intermediate shaft. 14. Insert a bar carefully between the gearbox and the subframe. 15. Lower the

How to Tighten Drive Belt on EZGO Golf Cart

Replace the belt if necessary. Step 5: Place the new or existing belt onto the pulley system. Step 6: Tighten the tensioner bolt until the belt is snug, but not too tight. Step 7: Use a torque wrench to ensure the proper

How do I tighten the generator belt on a 2002 PT

To tighten the Alternator belt, make sure the Pivot Bolt and Locking Nut are both loose (see image below). Then, turn the Adjusting bolt until the tension on the belt is at an adequate tension. Now, tighten up the Pivot Bolt and Locking nut. If

Step-by-Step Guide: How to Replace the 2014 Ford Fusion 1.5 Belt

In conclusion, the 2014 Ford Fusion 1.5 Belt Diagram is an essential tool for car owners looking to maintain their vehicle''s performance and reliability. By familiarizing themselves with the

How to tighten the generator belt of Fengjun 5 [PDF]

5 FAQs about [How to tighten the generator belt of Fengjun 5]

How do you tighten a generator belt?

Loosen the pivot bolts on the generator, then on the adjuster strap. To tighten the belt, use a strong piece of wood to pull the generator away from the engine - a hammer handle will do - while you test the belt tension with the other hand. When the tension is correct hold the generator firmly in that position and tighten the adjusting strap bolts.

How hard does a generator belt move when running?

But the belt should be checked and tightened the same was as the generator shown in the owners manual. At the looser end of the acceptable adjustment range, the belt can move a bit when running; not exactly a wobble but a vibration like a guitar string. No hard as long as it doesn't move on either pulley, just in between.

How do you know if a fan belt is too tight?

If you have to really push hard with your thumb on the middle of the fan belt to get it to deflect the factory spec of 0.6" then it's too tight. Firm pressure at most is all that's needed when checking the belt deflection. The amount of twist you can get varies with the style and width of belt, so I generally don't use that method here.

Can you run a fan belt too tight?

While you don't want to run the belt too tight, be aware that running the belt too loose not only limits the speed at which the fan will be driven (and thus the amount of cooling you'll get), but it can also damage the belt and lead to premature wear/failure.

How hard does a belt move when running?

At the looser end of the acceptable adjustment range, the belt can move a bit when running; not exactly a wobble but a vibration like a guitar string. No hard as long as it doesn't move on either pulley, just in between. I found only two spacers left in the pulley.

Solar Pro.